Comex Show 2010 is here again!!!

Due to popular demand,  we are opening 2 Service Booths!

Hall 6: Booth 6611 & 6553

 Hurry Down, Don't Miss Out !

Venue: Suntec City

Dates: 2nd Sep - 5th Sep 2010

Time: 12pm-9pm 

Long term relationship is of utmost importance to us and we have successfully built up a membership database of more than 10,000 members. Our core businesses include import, export, marketing and distribution.

Mini Sun Power Stabilizer FAQ & Working Principles

Q1. What is MiniSun PowerStabilizer and Electricity Saver?

It is a device that uses German technology to stabilize the electrical current, reduce power surges and improves power factor of your electrical appliances. In doing so, it reduces electrical overheating and saves power consumption in an electrical network.

Q2. Where is it manufactured?
 
In Malaysia by MINI SUN Inc.
 
Q3. How long has this device been in the market ?
 
 Since year 2000.
 
Q4. Which country is it in use?
 
Singapore, Malaysia, Philippines, Indonesia, Thailand and United Kingdom and world wide via on line purchase.
 
Q5. Is this device legal?
 
Yes. It has been approved by the Malaysian Energy Commissions (Sirim)
 
Q6. Is this Device guaranteed to save electricity?
 
Yes. Please see additional supplement Notes below.
 
Q7. How do I use it?
 
For a premise with a single phase wired system, simply plug the Minisun188 device into any available 13 Amps 3-pin plug. The 13 Amp power-point must be a original dedicated power point. Sharing with an adapter is not allowed. A temporary Extension Power point hook to a multiple extension socket is not allowed. There is no necessity to plug it as near to the Meter as possible. Leave it switched on. If you want to disconnect the device from the power point, switch off the switch at the power point and wait for 10 seconds before disconnecting the 3 pin plug to allow for power to dissipate. (There is power in the capacitor)
 
For a premise with a 3 phase wired system, consult a qualified electrician or consult the Seller of the Device. You can identify the 3 phase system by the red, blue and yellow power cables entering the meter. You will need to identify which phase carries the highest current and connect the Minisun388 into the respective 13 Amps socket.
 
Q8. It can be use in a Single Phase wired building. What about in 3 phase buildings?
 
Yes, it can be use in a 3 phase wired building as well. See Instructions on how to install it above.
 
Q9. How many percent of savings can I expect from using this device?
 
Between 10% to 20 % and more depending on various factors. (more details below)
 
Q10. Is there any maintenance required on this product?

No, this Device is maintenance free. There are no moving parts, it is not classed as an electrical appliance. Simply plug it into any 13 Amps socket and its done.
 
Q11. Is there a warranty or guarantee on the life span of this product?

Yes: see the Warranty Card when you purchase it. 1 year warranty from defects and 90 days money-back guarantee if you experience no savings from your electrical bill.
 
Q12. What are the limitations on the use of the Minisun?
 
This Device can be used in Shops, Home, Office, Restaurants, etc .
However it is not designed for loads in heavy duty settings.
 
 *Additional supplement notes on the Minisun below.
 
The following tips are helpful in determining why there is no reduction in the cost of the electric bills after installing the device for at least a month.
 
1.   Apparent non-reduction of the electric bill after one month of use. This happens when the Utility monthly bills is an estimated bill instead of actual metered bill.
 
2.   The Minisun Power Saver having been installed, has been left switched off after the power point has been used for other appliances.
 
3.   The device has been installed mid way after the reading of the previous bill or just before the next bill and so does not show a reduction when the bill comes. Too short a period to see the difference.
 
4.   Users electric power usage is not typical or consistent. Eg. Periods of heavy electrical usage fluctuating with periods of very low electrical usage. There is no constant pattern of use. This does not mean that the Minisun power saver is not working. An accurate way to judge this situation is to compare the actual bills and average them over 3 months to get a pattern of average monthly consumption and compare it with the preceding 3 months before installation of the Minisun.

5.   Additional equipment is installed by the User after the Minisun Power Saver Device has been installed. This in effect increases the electrical consumption of the premise over and above what the Minisun was originally designed for.
 
6.   User does not install the recommended number of units of Minisun calculated according to their monthly consumption, either due to lack of available power-points or installation of additional power-consuming appliances. The Minisun Power Saver is stretched to its limits and cannot perform efficiently.
 
7.   The same situation applies to a premise with 3 phase electrical wiring system. There are insufficient power-points to install the recommended number of devices to optimize the savings (i.e. install a lesser quantity than the recommended units).
 
Each unit of the MS388 can handle a monthly maximum load not exceeding 2000 KWH x 3 phase (6000KWH) and if a household's electrical load exceeds it, 2 units should be installed per phase or else the results will not show a reduction in power consumed as the device is overworked.  Eg. instead of installing 2 units recommended per phase, (2 for each phase), Owner only installs one unit in each of the 3 phase. Example, a customer merely installs 1 unit in a 3 phase wired building. The other 2 phases are not covered by the Minisun, hence the Minisun does not seem to work.
 
8.  Savings will be substantial on appliances with inductive loads (motor-related appliances like Air Cons, Freezers, fridge, Fans etc ). Savings will be less on heating elements.
 
9. The conditions of the household appliances also affects the performances of the Minisun. Well maintained appliances certainly cost less to operate (energy efficient) and if after installation of the device, owners neglect to continue maintaining the appliances (eg. Air-cons, servicing the filters, condensers, heat exchangers at the due intervals), this will make the electrical appliances work harder, hence increasing your electrical bill.
 
10. Ambient temperature also has an effect on the performance of the device. On hotter days, the air con will use more energy to cool the rooms and so the device while reducing the cost of the bills will have to work on higher parameters of ambient temperatures and extra load.  This will tend to give an "apparent" indication that the device does not work.  
 
Some air-cons are set on manual High cooling rate all the time and this will also result in apparent in-effectiveness of the Minisun.

Working Principles

All electrical supply is subject to surges from time to time, which result in spikes or parasitic peaks that cannot be used by your appliances as working power. These spikes simply consume electricity to no benefit. Worse still, they result in overheating, which shortens the life your appliances and wiring, and in extreme cases can cause burns, blow outs and power cuts.



The Minisun Power Saver uses a capacitor system to stabilize the flow of electricity. It reduces the spikes in the supply, protecting against surges. The system improves the power factor of your electricity and reduces your electricity bill by on average 15%.

The Minisun Power Saver will work on the whole circuit in your building (Single Phase). Field testing for a typical home consistently shows that the Power Saver will save 3 to 4 kw per day, based on electrical consumption of 30 kw per day. The amount of savings depends on a few factors, such as the types of electrical appliances, the time they are in use and the location. Places near to shops, restaurants and light industries, where the voltage supply is unstable and fluctuating will see higher savings. Where voltage supply is particularly unstable, the Power Saver can reduce electrical consumption by 30% or more.

The Power Saver reduces the reactive power generated by inductive loads. It extends the life span of an appliance’s motor, and helps the utility companies by eliminating interference to the power supply.

The Minisun also improves safety by reducing the overheating of electrical wiring. This in effect can lead to reduction in the size of wiring and copper loss. The Minisun also extends the life span of your electrical appliances. The Power Saver is made in Malaysia, and has been tested by PSB (Singapore) and SIRIM QAS Malaysia and checked for compliance with EU standards. Device is able to store electricity for 5 to 10 seconds and release it for use during downside voltage.

Technical Aspects

There are two components of power: reactive power and working (real) power.

•    Reactive power (kVAR) is used to create EMF in the inductive loads in your home
and business. This power performs no "real" work.

•    Working power (kW) is the power that performs the function of the load, i.e. turns the
drive shaft.

These two components combine to formulate Apparent Power (kVA), the total power
which the load consumes. Apparent power is equal to the square root of kW2 + kVAR2

Power Factor is the ratio of working power (kW) to apparent power (kVA). In other words, looking at all the power that a load consumes, how much of it (percentage wise) is used to perform the real work. A higher Power Factor means the electrical appliance is more efficient and consumes less electricity. The Minisun increases the Power Factor of an electrical appliance.

The Mini Sun Power Saver improves the power factor by reducing the amount of reactive power (kVAR) that the load draws from the utility company. This is accomplished by supplying the reactive power locally at the load by the use of capacitors. Capacitors store the reactive power (kVAR) needed for the creation of the EMF within the inductive load. As the motor operates, this reactive power is "pulled" and "pushed" to and from the capacitors by the motor. In simpler terms, it can said that inductive receivers (motors, transformers, etc) consume reactive energy, while capacitor (capacitive receivers) produce reactive energy. Therefore the amount of reactive power purchased from the utility company by a power factor optimization has been greatly reduced, or eliminated by use of the Minisun.

Conclusion
Benefit of increased Power Factor. Consumers whose applicable tariffs include MD* charges and Power Factor surcharge shall be able to reduce their energy demand and consumption, thus will benefit from both the reduced cost of energy and reduced consumption of electricity. Consumers whose applicable tariffs do not include MD* charges and Power Factor surcharge shall benefit from the reduction in energy consumption due to increased efficiency of their electrical appliances, reduces in losses and better voltage profiles.

Note:
•    MD =  Maximum Demand Meter

1)What does EPS stand for?

It stands for Efficient Power Systems- which is the name of the manufacturer in the UK.

2)WhAt's NOX emissions?

Nitrous Oxide- toxic gases to the environment. EPS fuel saver reduces these emissions, hence it means your petrol is combusted better and is more beneficial to the environment.

3)What's HC emissions?

Is it hydrocarbons? and same as carbons? Yes, you are correct.
WHich is more harmful to environment and health? Both are harmful.. but lower HC emissions means that your petrol is combusted better and less wastage from the engine. 10-20% savings.

4) Can you tell me how do you install this EPS into your vehicle?

Our mechanic will do all installations at our Kallang office- 44 Kallang Place, 4 Star Building.
We do not guarantee the performance of the fuel saver if it is installed by our customers themselves. It basically requires clamping the product around the fuel line entering the fuel injector. Takes less than 5 mins for installation by our qualified staff.

5) Where is it made in?

The product is researched & manufactured in the UK to the highest standards. We can provide all the official test-results certified by research labs in the UK. We have been successfully installing the EPS Fuel saver in over 7,600 cars in Singapore for the past 4 years. It is not some low quality product made in china/vietnam.

6) What maintenance does it require?

None! it is non-moving, hence no wear & tear. Just install it around the fuel line and it is ready to go!

7) Does it need to be replaced over time like due to wear and tear?

No need, product is guaranteed by manufacturer for 10 years, 2 year warranty for all products in Singapore, 1 to 1 exchange if product is found to be faulty. 30 day money back guarantee if you aren't satisfied with product. No risks!!

8) How much is it - the regular price?

Price of each EPS Fuel saver is $99.90, but price drops once you decide to become a member of our referral program. Membership is FREE once you purchase your first EPS Fuel saver. Your second EPS unit is $65 (ie, your friend orders from you and our company installs the product for your friend, you pocket the $35 rebate). More people order, or friends of your friends order, and you pocket $35 each time! Easy money.
 
Some members are making $5-7 k/month full-time. We have lots of other car gadgets apart from EPS.

9. Is the product approved by LTA?

No official paperwork from LTA (Land Transport Authority), but the product is 'plug & play', such that it can be easily removed from the vehicle in 5 secs (by cutting the tie-straps holding the 2 magnets to the fuel line). The driver can then tie-it back after the LTA inspection if he is paranoid. The device should pass since it’s not considered a physical or permanent modification to the engine. LTA does not provide approval documents for devices which do not alter the engine or increase environmental pollution (emissions or noise). In fact, the EPs Fuel saver is designed to reduce toxic environmental pollution!
 
10. Do you guarantee the performance of the product? (eg. up to 20% fuel saving)

Yes, fuel savings is guaranteed from 10-20%. Anything above that is determined based on the car, the condition of the engine, the style of driving of the driver and the type of road (expressway, city congestion etc). These factors are too variable to guarantee absolute % values- no one can! We have the technical manual with over 20 different test results if people are cynical. It’s like an athlete training, the more you train, the fitter you get. Same anology with the fuel saver- the longer you use it in the car, the greater % savings due to the improved condition of the car's fuel injector over time (de-carbonised). Don’t expect 20% savings in the first day after installation.. 20% over 1-2 months (or 500km above) is expected.
 
11. As i have a friend who did some scientific studies before that in order for this to perform fuel saving, it requires quite a huge magnet in order to do so. What's your comment?

Its not the size which matters, its how you use it!  EPS technology is patented 3-tier positive ions...cheaper rip-offs in the market only use 1 single magnet without guaranteed magnet strength! Also, the EPS is designed so that the positive magnetic charges are directed towards the fuel flowing though the fuel line, hence positively charging all fuel particles in the process.
 
12. Do we work with you as a distributor where you consign the goods out or do we get the order first before placing orders with you? And how can we have a sample piece to show to our customers?

It’s the latter, H2H Group provides the marketing tools such as fliers, you collect orders. We provide 1 or 2 samples for u to carry around (subject to refundable deposit). Once you have confirmed orders, contact us with the details of your customer (name, car model, phone number) and we’ll arrange the installation. Customer installs EPS, we pay you the referral of $35 each time,
 
13. How can you work out a scheme where all parties including myself will benefit, if i refer you to another person who wants to work as a distributor or has a pool of database which we can tap? (also, if that person has a car accessories shop which they will sell for you but need the products to be on display?)

We are currently working on this biz plan, so that all partners & managers get compensated fairly. Come to our office in Kallang to find out more. Generally, you are considered an ‘authorized distributor’ once you purchase your first EPS fuel saver. Anyone you recommend afterwards as a customer/distributor is considered your ‘referral’, and you will be paid commissions on your referrals who purchase a EPS fuel saver.

14. Do you provide installation? Who will do the installation?

We provide installation, but over time, all partners & managers are required to KNOW how to install the products. Installation by certified mechanics.. takes 5 mins to install. $20 labour and un-installation charges apply if customer returns and demands a refund on the product.

15. What is the Fuel Saver’s life span?

The device is designed using the best quality magnetic material with optimum Gauss level. Its life span is the same as your vehicle. Test indicate that the fuel saver retains it’s fuel saving abilities fpr up to 10 years. The field strength of the device does not deteriorate with time.
 
16. Are there cases, whereby after installation, no effects are seen?

Only in isolated cases where the vehicles are very old (20+ years), vehicles with carburetors or very bad maintenance records. Additionally, for very new vehicles (less than 10,000 km mileage), the fuel savings are not substantial. However, the fuel saver reduces waster fuel, hence reduces carbon deposits which will normally form on the fuel injectors - thus keeping your engine cleaner and lowering maintenance costs in the long term.

Hope these answers help in your decision in purchasing the EPS Fuel saver.
Give it a try! We offer money-back guarantee. Not only will you be Saving Money on your fuel costs, you will be helping to Save the Environment and Save your Engine!